PTU Tutorial - Bang That Beat Collab!

PTU tutorial using Bang that Beat collab by Karra's Kreative Korner & PinkParadox Productions! Bang that Beat is a rockin' collab with over 200 elements and 40 papers; it's definitely sure to make you groove! Get it today for just $3.50 at Pink Paradox Productions.

**This tutorial was written by me and any resemblance is purely coincidental. It is written for those with a working knowledge of Photoshop.**

Supplies

Scrap Kit

Bang That Beat by Karra's Kreative Korner 

& PinkParadox Productions

Template

Template 479 by Mille

Tubes

Music Love by Arthur Crowe

*You must obtain a license to use this tube.*

Elements

kk_bottle

kk_buttons

kk_guitar pick

kk_label

kk_note scatter

kk_screw line

kk_sparkle2

kk_speaker1

kk_vip pass

PPP

11

12

13

30

38

40

63

64

87

Papers

kk_paper5

kk_paper7

kk_paper16

PPP_Paper24

Let's start!

Open a new canvas, size 700x650.
Open the template and move it on to the canvas.

Only keep layer 2-9. Discard the rest.

Add a bevel and a drop shadow to each remaining layer, excluding layer 4.

Starting with kk_paper5, place it over layer 3 and create a clipping mask.

Duplicate the paper and place it above layer 2 and create a clipping mask.

Place kk_paper16 over layer 5. Create a clipping mask and resize.

Place kk_paper7 over layer 6. Create a clipping mask and resize.

Duplicate the paper and place it above layer 7 and create a clipping mask.

Select the pixels of layer 8 and fill with #bea5ca. Repeat for layer 9.

Select layer 4 and fill with white then drop the fill to 50%.

On top of four use a small font to write out bang that beat repeatedly across the back in black.

Place the tube in the middle of the template. Resize and add a drop shadow.

In front of the tube, place the screw line. Resize and add a drop shadow.

Take a close up of the tube and place it over layer 8 and create a clipping mask. Resize and change to Luminosity.

Duplicate the close up and place it over layer 9 and create a clipping mask.

Place speaker1 behind and to the left of the tube. Resize and add a drop shadow.

Duplicate the speaker and flip horizontally then move to the right side of the tube.

Place kk_sparkle2 on the top circle on the speaker on the right and resize.

Duplicate the sparkle and place it on a circle on the left side.

In front of the tube on the right, place kk_bottle. Resize and add a drop shadow.

Behind the bottle, place ppp_11. Resize and add a drop shadow.

In front of the bottles, place ppp_40. Resize and add a drop shadow.

To the right and behind ppp_11, place ppp_30. Resize and add a drop shadow.

Behind the sunglasses and in front of the cash, place ppp_63. Flip horizontally, resize, and add a drop shadow.

Duplicate ppp_63 and flip horizontally. Move to the opposite side of the template.

On top ppp_63, place kk_buttons. Resize and add a drop shadow.

On the left side of the tube, place ppp_38 in front of the tube. Resize and add a drop shadow.

To the left of the camera, place kk_guitar pick. Resize and add a drop shadow.

In front of the guitar pick, place kk_vip pass. Resize and add a drop shadow.

On top of ppp_63 on the left, place ppp_64. Flip the mic vertically and horizontally. Resize and add a drop shadow.

Behind layer 8, place kk_label. Resize and add a drop shadow.

Place ppp_13 behind layer 9 on the right side. Resize and add a drop shadow.

Place kk_note scatter behind the template around the tube and resize. Erase anything that hangs too far off the template.

Select the pixels of the note scatter and expand by two. Add a layer below and fill with white and add a drop shadow.

Place ppp_87 underneath the tag on the right side. Resize and move so just a larger star sticks out. Erase the rest.

Duplicate the star and flip horizontally then move to the left side.

Behind the note scatter, place ppp_12 and flip horizontally. Resize and add a drop shadow.

Add your tagger mark and copyright information.

Crop off any extra canvas.

Save as a .psd & .png.

Free snags!

Thank you for coming by!