Friday, August 23, 2013

PTU Tutorial - 2013 BB Dead Sexy by Ismael Rac!

PTU tutorial using the new tube by Ismael Rac called 2013 BB Dead Sexy!
You can purchase the tube and matching kit at the Xeracx store!
**This tutorial was written by me and any resemblance is purely coincidental. It is written for those with a working knowledge of Photoshop.**

Supplies
Font

Mask

Scrap Kit

Template
(Scroll down to the Halloween templates.)

Tube
*You must obtain a license to use this tube.*

Elements
Bloody
BloodyEye2
Bonecake
Bow1
Bracelet
BrainIceCreamCone
Cat
Flower2
Halloween Pumpkins
Lips1
Lipstick1
Needle02
Perfume1
Satin Ribbon2
Satin Ribbon3
Skull3
SkullnCandle
Sparkles1
Swirl1

Papers
 1
5
7
8
9
10
11

Let's start!
Open a new canvas, size 650x650.
Open the template, link the layers together, and move on to the canvas.
Delete the word art layers and credits.
Resize the template if you like.
On layer 1, place paper05, flip it horizontally, and create a clipping mask.
Take paper11 and create a clipping mask to layer 2. Add a drop shadow to both layers 1 & 2.
Select the pixels of layer 3 and fill with #93a53a. Add a drop shadow.
Fill layers 4 & 6 with paper 10. Resize and create a clipping mask on both layers.
Select the pixels of layer 4 and expand by 4. Make a new layer underneath the 4th layer and fill with #93a53a. Add noise and a drop shadow. Repeat the steps for layer 6.
For layer 5, place paper 1 over it and create a clipping mask. Resize as needed and add a drop shadow to the layer.
Add the same paper to layer 7. Add a drop shadow to the layer (may be covered up later).
Place paper 7 over layer 8 and create a clipping mask. Select the pixels of the circle and expand by 3 make a new layer underneath it and fill with #9b2ab7. Add noise and a drop shadow.
Move paper 8 over layer 9 and create a clipping mask. Select the pixels of layer 9 and expand by 4. Create a new layer underneath layer 9 and fill with #93a53a. Add noise and and a drop shadow.
That should be it for the template. Now let's open the tube. Place the full size tube in front of the template, in the middle. Resize and add a drop shadow.
Take the close up of the tube and place in over layer 1 and create a clipping mask. Have one copy of the close up to the left of the tube and then a larger copy on the right side, flipped horizontally.
Erase where they may overlap.
Behind the green circle, place swirl1. Resize and add a drop shadow.
Place a copy of bloody on top of the green circle and purple paper (behind the main squares) on the left side and right side. Erase anything off the template.
Place the skullncandle on the left side. Resize and add a drop shadow.
Behind the skullncandle, place the bracelet toward the left. Resize and add a drop shadow.
Place the brainicecreamcone behind the skullncandle toward the right. Resize and add a drop shadow.
Between the candle and cone, place lipstick1. Resize and add a drop shadow.
To the left of the candle and bracelet, place two of the flower2. Resize and add a drop shadow.
Next to the cone and candle, place the bonecake. Resize and add a drop shadow.
Behind the bonecake, place lips1. Resize and add a drop shadow. Make sure the lips are behind the tube as well.
Between the lips and bonecake, place the bloodyeye2. Place it behind the tube at her feet. Resize and add a drop shadow.
Next to the eye, place perfume1. Resize and add a drop shadow. Again, make sure it's behind the tube.
Place the cat in front of the perfume. Resize and add a drop shadow.
Place skull03 behind and to the right of the cat. Resize and add a drop shadow.
Move needle02 behind the cat. Resize and add a drop shadow.
Behind the needle, place the halloween pumpkins on the right side. Resize and add a drop shadow.
Take the flowers from earlier, duplicate them, flip them horizontally, and place them between the skull03 and pumpkins. 
Duplicate the flowers again and place them to the left of the pumpkins. Add another copy of the flowers over the frame behind the tube also.
Take satin ribbon 2 and place it on top of the green circle behind the two main squares. Resize and add a drop shadow.
On top of the ribbon, place bow1. Resize and add a drop shadow.
Place satin ribbon 03 on top of layer 4 behind the main squares. Resize and add a drop shadow.
Duplicate and place bow1 over the lower left hand corner of the top square.
 Now take sparkles1 and place it on top of the elements and tube on the left side. Erase some of the sparkles so it's not overcrowded. Also erase anything off the tag. Take another copy of the sparkles and place it on the right side of the tag. Again erase some of the sparkles so it's not overcrowded.

Mask
Open a new canvas, size 600x600.
Move paper 9 on to the blank canvas. 
Open the mask and move on top of the paper.
Remove the white background and place the mask behind the tag. 
Make it evenly stretched on all sides, but not hanging off the canvas.

 Name
Main color is black.
Add a stroke, size 2, in color #90a431.
Change the bevel to Rounded Steps.
Add noise and add a drop shadow.

Add your tagger mark and copyright information.
Crop off any extra canvas.
Save as a .psd & .png.
We're done :)

And here are free snags for you!

New Name, New Blog!

Hello friends! I have decided to change my designer name to reflect that I make kits more than I do CT work. I made a new blog so the old links for this blog will remain active for future visits. Please visit me at Drea's Designs ! I'll see you there!
Related Posts Plugin for WordPress, Blogger...